Stainless Steel Wire Calculator


Ultra Fine Stainless Steel Wire
Stainless Steel Wire
Stainless Steel Cold Heading Wire
Stainless Steel EPQ Wire
Stainless Steel Machining Wire
Stainless Steel Forming Wire
Stainless Steel Spring Wire
Stainless Steel Cable Rope
Stainless Steel Alloys
FEP Coated Stainless Steel cable
Insulated Stainless Steel Single Wire

Types of Stainless Steel:

Stainless Steel Wire 302
Stainless Steel Wire 304
Stainless Steel Wire 310
Stainless Steel Wire 314
Stainless Steel Wire 316
Stainless Steel Wire 317
Stainless Steel Wire 321
Stainless Steel Wire 347
Stainless Steel Wire 410
Stainless Steel Wire 412
Stainless Steel Wire 420
Stainless Steel Wire 430
Stainless Steel Wire 434

Stainless Steel Technical Info:

Stainless Steel Wire Technical
Stainless Steel Wire Calculator
Stainless Steel Wire Composition Chart
Stainless Steel Alloy Ft/lb chart
Stainless Steel Alloy Comparsion Chart
Stainless Steel Wire Cross Reference Chart













Stainless Steel Wire and Cable

Stainless steel wire can be produced to with a diameter of about 13 microns, that is about one-sixth the thickness of a strand of hair. This is widely used in mesh for screen printing, electronic circuit boards and even clothing applications. The increased life of stainless steel ad to the longevity of the products. This gives your products a longer life before becoming extinct. Not to mention that stainless steel is one of the most cleanest and environmentally friendly processes in the steel industry.

What is Stainless Steel?

Stainless steel’s resistance to corrosion and staining, low maintenance, relatively low cost, and familiar luster make it an ideal base material for a host of commercial applications. There are over 150 grades of stainless steel, of which fifteen are most common. The alloy is milled into coils, sheets, plates, bars, wire, and tubing to be used in cookware, cutlery, hardware, surgical instruments, major appliances, industrial equipment, and as an automotive and aerospace structural alloy and construction material in large buildings. Storage tanks and tankers used to transport orange juice and other food are often made of stainless steel, due to its corrosion resistance and antibacterial properties. This also influences its use in commercial kitchens and food processing plants, as it can be steam cleaned, sterilized, and does not need painting or application of other surface finishes.

Stainless steel is also used for jewellery and watches. The most common stainless steel alloy used for this is 316L. It can be re-finished by any jeweller and will not oxidize or turn black.

Some firearms incorporate stainless steel components as an alternative to blued or parkerized steel. A few, more expensive revolvers (like the Smith and Wesson Model 60) and pistols (like versions of the Colt M1911) are milled entirely from stainless steel. This gives a high-luster finish similar in appearance to nickel plating; but, unlike plating, the finish is not subject to flaking, peeling, wear-off due to rubbing (as when repeatedly removed from a holster over the course of time), or rust when scratched.

300 Series Stainless Steels.

This group of alloys are non-magnetic and have an austenitic structure. The basic alloy contains 18% chromium and 8% nickel. These alloys are subject to crevice corrosion and pitting. They have a range of incubation times in seawater ranging from essentially zero in the case of the free machining grades, such as Type 303, to 6 months to 1 year for the best alloys, such as Type 316. They have been widely used in facilities with mixed results. If used in an application where chloride levels are low or where concentration cell corrosion has been prevented through design, they are likely to perform well. When chloride levels are high and where concentration cells can occur, the performance of these alloys is often poor. They must always be selected with care for a specific application and the effect of potential non-uniform attack on system performance must be addressed.

400 Series Stainless Steels.

This group of alloys are magnetic and have a martensitic structure. The basic alloy contains 11% chromium and 1% manganese. These alloys can be hardened by heat treatment but have poor resistance to corrosion. They are subject to both uniform and non-uniform attack in seawater. The incubation time for non-uniform corrosion attack in chloride containing environments is very short, often only hours or a few days. Unless protected, using these alloys in seawater or other environments where they are susceptible to corrosion is not recommended.

Stainless Steel Wire Production Capabilities:

Shaped Wire Thickness Range: 0.005" - 0.335" (can do +/-)
Width Range: 0.020" - 1.50" (can do +/-)
Flat Wire  Thickness Range: 0.0002" - 0.210" (can do +/-)
Width Range: 0.002" - 1.50" (can do +/-) 
  Square Wire Thickness Range: 0.030" - 0.250" (can do +/-)
Width Range: 0.030" - 2.50" (can do +/-)   
  Round Wire Diameter Range: 0.00075"- 0.102"  (can do +/-)